VIKING II: DISASSEMBLY

The first stage of fixing up this old transmitter is disassembly.  When Johnson built their gear they certainly didn’t spare the fasteners.  This thing is held together by a ton of slotted head screws.  Took forever to remove them all.  Fortunately, the cabinet came apart really easy.  The hardest part was removing the front

face.  Once I had all the pieces separated I got busy with a bottle of Formula 409 cleaner and paper towels.  This works pretty well on most stuff.  I also used a tooth brush to really scrub the parts that had a course exterior finish.  It didn’t work miracles, but for a transmitter nearing 70 yrs old it’s not too bad.

I now have access to the chassis of the beast.  I’m impressed with the overall design, construction, layout, and quality.  You can really tell these were built to last.  The top side will definitely need some scrubbing, but I don’t see rust or corrosion.  Of specific interest is the ganged, gear-driven variable inductor/capacitor tuning unit.  Not only is it exceedingly grungy, but it’s not operating correctly.  I believe this is the only item of concern up top.

                                  

The bottom of the chassis also looks as expected.  A little dusty and some spider webs, but pretty clean.  Fortunately, no surprises down there.  I will have many electrolytic and waxy caps that will need replaced.  Since I don’t own a leakage tester I’ll just have to assume they’re all suspect at this age.  The worst thing is to let electronics just sit.  Even very old components will continue to perform for decades if they’re just used regularly.  I’ll also have to do some checks on the resistors as they’ve probably drifted, too.  Some components are more critical than others depending on the particular circuit.  This will just take some time to research the usual suspects and start ordering.

 

Fortunately, Johnson made a lot of these transmitters.  I’d like to purchase a manual reprint but was able to easily find a PDF on the BAMA website.  I’ve found them to be very helpful for everything except Heathkit (because of copyright licensing).  I’ve had good luck purchasing reprints from Manualman and others.

Here’s a pic of this big honkin’ oil filled cap.  No reason to include it except it’s cool.  Just another example of the quality put into these rigs.  Hoping to get the chassis all cleaned up and the roller inductor functional again.  That will complete the first phase of the project.  I think the next part will be more fun.  I like working with components better than cleaning stuff up.  Stay tuned.

TIME TO BEGIN AGAIN: VIKING II

It appears as though I haven’t made a post in over a year.  Time flies when you’re having fun…or extremely busy.  It’s time to start a new project.  In doing so, it might be fun to document the progress here in cyberspace (does anyone even still say that).  It’s a good way to keep track of what’s been done, and also share with friends.  Often times it might also be a topic of interest to many others outside your local chums.  My posts on the ARD 230 project sure generated a lot of feedback from other owners.  I received inquiries from hams as far as Spain and Germany!  Strap in for the ride…here it begins.

I got energized to try something new after participation in the AM Rally early this spring.  I’ve always been interested in vintage radio and the roots of our hobby.  While CW holds the crown as oldest mode, AM isn’t too far behind.  Many modern and vintage radios will operate AM, but I get a kick out of using vintage gear to operate a vintage mode.  My lash-up for the event was a Heathkit DX-60A transmitter with the matching HG-10 VFO and Astatic D-104 mic.  Classic 60’s and good for about 55W PEP.  The receiver was a Yaesu FRdx-400.  Early 70’s production, and it did pretty well for me, too.  I didn’t yet have a dowkey relay so all the switching was done manually.  Let me tell you, that’s a lot of work just to complete an exchange!  My time was limited, and I made only one contact but I think the hook was set.  Time to finally breath new life into this old gear that’s been sitting around cluttering up my shack.

Ten years ago I purchased a Johnson Viking II transmitter from a good friend and elmer Joel, K2LYC (now SK).  I also came home with several other vintage pieces from his extensive collection, but that will become the subject matter of many future posts.  The intent was to setup an AM station (Studio B) to accompany my then-modern Icom IC-756 station (Studio A).  Somehow a decade passed away and, sadly, so did Joel.  I guess I feel like I owe it to him to get this stuff playing again.  So, it begins with the transmitter.  I’m going to start there because usually they’re simpler.  I’ve also had pretty good success fixing others.  Fortunately, there’s loads of info available at my fingertips.  This is the intro so I’m not going too deep.  My plan is to remove the chassis from the cabinet for overall cleaning and inspection.  I’ll replace any faulty components and perform only the mods that are proven and considered best practice.  No total restoration needed.  I’m sure every scratch and scrape tells a story.  It’ll never be a mint specimen, just an honest workhorse.  Eventually it’ll pair with my Collins 75A-3 (which will probably be the next project).  But you see I’m already ahead of myself.  Next post will start getting into the real heart of the job.  73!